FULL FEATURE DESCRIPTIONS:

ControlTL™
PocketWizard’s newest firmware platform taps into the camera’s digital communications to enable an entirely new level of remote flash capability through our proven radio system. ControlTL allows remote i-TTL for Nikon CLS / i-TTL systems as well as Manual Power Control. ControlTL firmware is configurable and upgradeable for “future-proof” continuous improvement.

Dedicated CLS / i-TTL Triggering
Locking your FlexTT5 Transceiver into the hot shoe of a Nikon DSLR camera, and mounting CLS / i-TTL flashes onto FlexTT5 Transceivers gives you full flash exposure control with the freedom and reliability of a PocketWizard radio. There are no special settings to make or modes to call up. Use the camera’s exposure compensation controls for basic control of remote flashes, or add an AC3 ZoneController or Nikon Master unit for even more flexibility.

Manual Power Control
Adjust the manual power settings of your remote Nikon Speedlights directly from a SB-800, SB-900 flash or PocketWizard AC3 ZoneController mounted on your on-camera FlexTT5. Working with a Nikon SB-800, SB-900 or AC3 in the shoe of the FlexTT5, you can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting. Now you can work with total control with your remote lights, without leaving your shooting position. Nikon SU-800 Wireless Speedlight Commander may also be used.

Zone Select
The FlexTT5 Transceiver has an A-B-C zone select switch to allow use with the remote groups/zones found on on the PocketWizard AC3 ZoneController or Nikon flashes. Zones allow you to control single or groups of lights independently from other lights in different zones. These zones can also be used with a MultiMAX thus allowing you to pair a single MultiMAX radio on camera with FlexTT5s Transceivers on your remote flashes and utilize many of the MultiMAXs advance trigger functions.

HyperSync™ Automation
HyperSync Automation adjusts HyperSync timing in two separate places – on the transmitter and on the receiving ControlTL radio. The transmitting or on-camera MiniTT1 or FlexTT5 automatically adjusts HyperSync to compensate for changes made to shutter speed. Photographers can further refine HyperSync via the PocketWizard Utility. For more information on Configuring HyperSync Automation, visit the HyperSync section of the PocketWizard Wiki.

High Speed Sync (Auto FP)
When HyperSync can’t keep up, FP/High Speed Sync takes over for Speedlight flash photography all the way to 1/8000. Use this feature to shoot wide open in bright sun for amazing results.

High Speed Sync (HSS / FP Sync) Disable Mode
Select either HSS Sync or HyperSync™ at shutter speeds above x-sync. This allows you to use HyperSync and the benefit of full power flash all the way up to 1/8000 with certain flash systems.

Rear Curtain Sync
Precise rear curtain sync capability is engaged using the cameras sync settings. Capture natural light trails with sharp exposures at the end – no “after trails!”

Pre-Flash Boost
Nikon flashes use a dual preflash system to calculate i-TTL exposure values. In many TTL situations, including shooting in full sun, over long distance or using diffusers or bounce flash, the normal pre-flash is simply not enough for the camera to see. PocketWizards Pre-Flash Boost increases your remote Nikon flashes first preflash by three stops and, if necessary, the second preflash by one stop. The boost level can also be adjusted at the flash if necessary.

PowerTracking
When working with the PowerST4, PowerMC2 and AC9/FlexTT5 paired with compatible manual flashes, you can change any of your settings on your camera and the system adjusts for those changes. Change your exposure compensation to adjust the exposure or make adjustments in aperture or ISO and the system balances your flash for proper exposure.

Basic Trigger Mode
Allows the FlexTT5 to work as a transmitter on ANY camera it will fit.